Research Article
BibTex RIS Cite

Analysis of the Effect of Switching Frequency on Acoustic Noise in External Rotor Brushless DC Motors

Year 2024, Volume: 12 Issue: 1, 98 - 104, 01.03.2024
https://doi.org/10.17694/bajece.1322919

Abstract

Electric motors are actively used in various industries. Acoustic noise is crucial in electric motors, and specific standards are depending on their application areas. Despite better performance, including acoustic noise, than brushed motors, brushless motors still generate acoustic noise due to their mechanical, electrical, and electronic components. This study investigated the impact of varying the switching frequency through the driver on the acoustic noise of an external rotor brushless DC motor. Tests were conducted on a surface-mounted magnet brushless motor with different switching frequencies, and detailed information about the sections of the control board governing the brushless motor was provided. The study includes measurements of motor speed, current, switching frequency, phase signal, and acoustic noise measured at two different locations in decibels. It was observed that the acoustic noise increased at specific switching frequencies. Furthermore, the variation in switching frequency also affected the heating due to losses in the switching elements. Increasing the switching frequency in the 12-28 kHz range reduced motor speed and the measured acoustic noise, while temperature increases were observed in various frequency ranges.

References

  • [1] M.R. Hazari, E. Jahan, M.E. Siraj, M.T.I. Khan, A.M. Saleque. “Design of a Brushless DC (BLDC) motor controller.” In 2014 International Conference on Electrical Engineering and Information & Communication Technology. IEEE, 2014, pp 1-6.
  • [2] P. Yedamale. “Brushless DC (BLDC) motor fundamentals.” Microchip Technology Inc, vol. 20.1, 2003, pp 3-15.
  • [3] R.M. Pindoriya, A.K. Mishra, B.S. Rajpurohit, R. Kumar. “An analysis of vibration and acoustic noise of BLDC motor drive.” In 2018 IEEE Power & Energy Society General Meeting (PESGM), 2018, pp 1-5.
  • [4] P. Mishra, A. Banerjee, M. Ghosh, S. Gogoi, P.K. Meher. “Implementation and validation of quadral-duty digital PWM to develop a cost-optimized ASIC for BLDC motor drive.” Control Engineering Practice, vol. 109, 104752, 2021.
  • [5] K. Nakata, M. Sanada, S. Morimoto, Y. Takeda. “Noise reduction for switched reluctance motor with a hole.” Proceeding Power Converters Conference, vol. 3, 2002, pp 971-976.
  • [6] E. Serdar, Izci D., Yilmaz M. "Efficient speed control for DC motors using novel Gazelle simplex optimizer." IEEE Access, 2023, pp. 105830 – 105842.
  • [7] X.T. Bai, Y.H. Wu, K. Zhang, et al. “Radiation noise of the bearing applied to the ceramic motorized spindle based on the sub-source decomposition method.” J. Sound Vib., 410, 2017, pp 35-48.
  • [8] D.J. Kim, H.J. Kim, J.P. Hong, et al. “Estimation of acoustic noise and vibration in an induction machine considering rotor eccentricity.” IEEE Trans. Magn, vol. 50, 2, 2014, pp 857-860.
  • [9] H.J. Lee, S.U. Chung, S.M. Hwang. “Noise source identification of a BLDC motor.” Journal of mechanical science and Technology, vol. 22, 2008, pp 708-713.
  • [10] A. Lelkes, J. Krotsch, R.W. De Doncker. “Low-noise external rotor BLDC motor for fan applications in Conference Record of the 2002 IEEE Industry Applications Conference.” IEEE, vol. 3, 2002, pp 2036-2042.
  • [11] A. Sathyan, N. Milivojevic, Y.J. Lee, M. Krishnamurthy, A. Emadi. “An FPGA-based novel digital PWM control scheme for BLDC motor drives.” IEEE Transactions on Industrial Electronics, vol. 56. 8, 2009, pp 3040-3049.
  • [12] D.H. Cho, K.J. Kim. “Modeling of electromagnetic excitation forces of an induction motor for vibration and noise analysis.” Proceeding of the KSME Autumn A, 18 (2), 1997, pp 372-377.
  • [13] S. Nau, H. Mello. “Acoustic noise in induction motors: causes and solutions.” IEEE 2000 Petroleum and Chemical Industry Technical Conference, 2000, pp 253-263.
  • [14] B. Weilharter. “Noise Computation of Induction Machines.” 2012.
  • [15] S. Zuo, F. Lin, X. Wu. “Noise analysis, calculation, and reduction of external rotor permanent-magnet synchronous motor.” IEEE Trans. Ind. Electron., vol. 62.10, 2015, pp 6204-6212.
  • [16] T.M. Jahns, W.L. Soong. “Pulsating torque minimization techniques for permanent magnet AC motor drives-a review.” IEEE Transactions on industrial electronics, vol. 43. 2, 1996, pp 321-330.
  • [17] K.S. Kim, C.M. Lee, G.Y. Hwang, et al. “Effects of the number of poles on the acoustic noise from BLDC motors.” Springer J. Mech. Sci. Technol., vol. 25. 2, 2011, pp 273-277.
  • [18] A. Glowacz. “Thermographic fault diagnosis of ventilation in BLDC motors.” Sensors, 21(21), 2021, 7245.
  • [19] K.T. Chau, C.C. Chan, C. Liu. “Overview of permanent magnet brushless drives for electric and hybrid electric vehicles.” IEEE Transactions on Industrial Electronics, vol. 55, 6, 2008, pp 2246-2257.
  • [20] P.C. Desai, A. Emadi. “A novel digital control technique for brushless DC motor drives Current control.” IEEE Electronics Machine Drives Conference, 2005, pp 326-331.
Year 2024, Volume: 12 Issue: 1, 98 - 104, 01.03.2024
https://doi.org/10.17694/bajece.1322919

Abstract

References

  • [1] M.R. Hazari, E. Jahan, M.E. Siraj, M.T.I. Khan, A.M. Saleque. “Design of a Brushless DC (BLDC) motor controller.” In 2014 International Conference on Electrical Engineering and Information & Communication Technology. IEEE, 2014, pp 1-6.
  • [2] P. Yedamale. “Brushless DC (BLDC) motor fundamentals.” Microchip Technology Inc, vol. 20.1, 2003, pp 3-15.
  • [3] R.M. Pindoriya, A.K. Mishra, B.S. Rajpurohit, R. Kumar. “An analysis of vibration and acoustic noise of BLDC motor drive.” In 2018 IEEE Power & Energy Society General Meeting (PESGM), 2018, pp 1-5.
  • [4] P. Mishra, A. Banerjee, M. Ghosh, S. Gogoi, P.K. Meher. “Implementation and validation of quadral-duty digital PWM to develop a cost-optimized ASIC for BLDC motor drive.” Control Engineering Practice, vol. 109, 104752, 2021.
  • [5] K. Nakata, M. Sanada, S. Morimoto, Y. Takeda. “Noise reduction for switched reluctance motor with a hole.” Proceeding Power Converters Conference, vol. 3, 2002, pp 971-976.
  • [6] E. Serdar, Izci D., Yilmaz M. "Efficient speed control for DC motors using novel Gazelle simplex optimizer." IEEE Access, 2023, pp. 105830 – 105842.
  • [7] X.T. Bai, Y.H. Wu, K. Zhang, et al. “Radiation noise of the bearing applied to the ceramic motorized spindle based on the sub-source decomposition method.” J. Sound Vib., 410, 2017, pp 35-48.
  • [8] D.J. Kim, H.J. Kim, J.P. Hong, et al. “Estimation of acoustic noise and vibration in an induction machine considering rotor eccentricity.” IEEE Trans. Magn, vol. 50, 2, 2014, pp 857-860.
  • [9] H.J. Lee, S.U. Chung, S.M. Hwang. “Noise source identification of a BLDC motor.” Journal of mechanical science and Technology, vol. 22, 2008, pp 708-713.
  • [10] A. Lelkes, J. Krotsch, R.W. De Doncker. “Low-noise external rotor BLDC motor for fan applications in Conference Record of the 2002 IEEE Industry Applications Conference.” IEEE, vol. 3, 2002, pp 2036-2042.
  • [11] A. Sathyan, N. Milivojevic, Y.J. Lee, M. Krishnamurthy, A. Emadi. “An FPGA-based novel digital PWM control scheme for BLDC motor drives.” IEEE Transactions on Industrial Electronics, vol. 56. 8, 2009, pp 3040-3049.
  • [12] D.H. Cho, K.J. Kim. “Modeling of electromagnetic excitation forces of an induction motor for vibration and noise analysis.” Proceeding of the KSME Autumn A, 18 (2), 1997, pp 372-377.
  • [13] S. Nau, H. Mello. “Acoustic noise in induction motors: causes and solutions.” IEEE 2000 Petroleum and Chemical Industry Technical Conference, 2000, pp 253-263.
  • [14] B. Weilharter. “Noise Computation of Induction Machines.” 2012.
  • [15] S. Zuo, F. Lin, X. Wu. “Noise analysis, calculation, and reduction of external rotor permanent-magnet synchronous motor.” IEEE Trans. Ind. Electron., vol. 62.10, 2015, pp 6204-6212.
  • [16] T.M. Jahns, W.L. Soong. “Pulsating torque minimization techniques for permanent magnet AC motor drives-a review.” IEEE Transactions on industrial electronics, vol. 43. 2, 1996, pp 321-330.
  • [17] K.S. Kim, C.M. Lee, G.Y. Hwang, et al. “Effects of the number of poles on the acoustic noise from BLDC motors.” Springer J. Mech. Sci. Technol., vol. 25. 2, 2011, pp 273-277.
  • [18] A. Glowacz. “Thermographic fault diagnosis of ventilation in BLDC motors.” Sensors, 21(21), 2021, 7245.
  • [19] K.T. Chau, C.C. Chan, C. Liu. “Overview of permanent magnet brushless drives for electric and hybrid electric vehicles.” IEEE Transactions on Industrial Electronics, vol. 55, 6, 2008, pp 2246-2257.
  • [20] P.C. Desai, A. Emadi. “A novel digital control technique for brushless DC motor drives Current control.” IEEE Electronics Machine Drives Conference, 2005, pp 326-331.
There are 20 citations in total.

Details

Primary Language English
Subjects Electrical Engineering (Other)
Journal Section Araştırma Articlessi
Authors

Buğra Er 0000-0002-3982-5654

Berk Demirsoy 0009-0003-3489-7346

Ahmet Fenercioglu 0000-0002-1522-6868

Publication Date March 1, 2024
Published in Issue Year 2024 Volume: 12 Issue: 1

Cite

APA Er, B., Demirsoy, B., & Fenercioglu, A. (2024). Analysis of the Effect of Switching Frequency on Acoustic Noise in External Rotor Brushless DC Motors. Balkan Journal of Electrical and Computer Engineering, 12(1), 98-104. https://doi.org/10.17694/bajece.1322919

All articles published by BAJECE are licensed under the Creative Commons Attribution 4.0 International License. This permits anyone to copy, redistribute, remix, transmit and adapt the work provided the original work and source is appropriately cited.Creative Commons Lisansı